Respirators and other safety tips for spraying sealant?

Spray outside. Actually I spray outside with a head on a soda bottle, and my head turned away . I must look ridiculous. But I have only done it a couple of times. Well done face ups a couple of time, multiplr sprays in between. If you're doing it a lot you may want to look for a good mask at a hardware store.

 

I agree, if you don't have a mask you should always at least turn your head and walk away from the area you have just sprayed.

That said I recommend getting a mask if you anticipate doing lots of faceups. Make sure you get one that works for sprays. I just took a pic of the one I use, it came from Home Depot. It was a bit over $30; it has two removable/replaceable cartridges, though I haven't had to replace it yet and have used it several times. It comes with a thick pamphlet of detailed info. (which I can't find, argg).

After reading in the forums about people becoming ill or worse, it scared the crap out of me into getting one!




I also still turn away and walk away from the area after spraying while wearing the mask.

 

I had myself a little MSC party this afternoon, and I would definitely suggest not spraying it without some type of protection.

Since I was outdoors I initially didn't use any hand or face covering, but after the first pass I realized how truly strong the fumes are and opted for latex gloves and a cotton handkerchief (tied bandit style) around the lower half of my face (I wear glasses).

I think that was sufficient, though if you're going to do this often you might want to invest in a mask from Home Depot or something. I'm interested in this one I just found on their website:



It's called the AO Safety Organic Vapor, Paint & Pesticide Respirator (Model 95122-00000), and best of all, it's $20. :grin:

 

I never bothered, I just MSC'd out in the garden when it was the right temp... kept well back, then left my boy outside for a while and nothing bad has become of me. I think it depends on how much you're planning to use.

 

I have respiratory issues, and I use a respirator whenever I spray anything. You DO NOT want to breath this stuff. Trust me. Make the investment, and you'll have the thing for life.

 

I never used a mask either, but sprayed outside, holding the thing away from me. Also, I'd pay attention to the wind-direction, as long as it blows away from you it should be fine.

 

Same thing as I did, sprayed outside and stayed away from the fumes. But they are really strong so I think I will invest in a mask. Especially as I plan to be sanding some resin soon.

 

Throw me in with the group that took the chance and simply sprayed outside - I set the head on a cart we had at the side of the house, tied a cloth around my face, and moved away when taking a breath (and when I got tired of running in and out between coats, set the head in an open, unscreened window and sprayed toward the outdoors ^^; ). I don't necessarily recommend it - there were a couple of times I got the scent of the chemicals pretty good - but since I know I'm likely to freak out if I have anything more than cloth over my face... My body is already shot to hell anyway, so there's probably not a lot left to damage at this point. ^^;

 

Mmmm...this thread is reminding me that I was going to follow up a similar question in another thread...but I feel weird telling people how to conduct themselves.

Perhaps, part of the issue here is informational. It is important to understand what exactly a solvent-type coating is and how its toxicity can affect you. MSC is HIGHLY flammable and HIGHLY toxic - states it clearly on the can. I don't know what all of its ingredients are and would be very interested if someone here does have that list. However, it IS a solvent-type coating and is aerosol propelled...so, it is something that needs to be used with caution even not knowing the full list of toxicity and/or carcinogenic properties.

A niosh-approved respirator would be a wise investment if you are going to be spraying regularly with it. If you are going to be using more than half a can at a time - say, for a full body coating - you've moved into a far more serious level of usage and should truly understand what it is you're working with.

Inhalation of any toxic chemical is not good for you - systemically - but with any type of product that "coats" something, you have to realize that that "coating" can "coat" the cilia in your lungs and that damage is not reversible.

Be careful.

 

Ah...of the few coatings I've done, I've always used a mask, gloves, and anything else I could. MSC is dangergous...I remember someone (I don't remember who) was spraying some when a freak wind happened and they ended up inhaling the stuff and it seared their throat and did all sorts of bad jazz....

 

I've never used a mask when sraying msc, but I probley should, I always trend to hold my breath while spraying but then, when I'm done I always tend to take a big deeep breath forgetting that the air around me is msc, so I always inhale a bit of it ^^;; I have'nt had any weird side affects or anything, but I should probley get one of those medical masks atleast ><;; heh

 

Home Depot also has a mask that is for both aerosol sprays (like MSC) & dust (like resin, if you're sanding) ... it's about $30. They also have masks for just one or the other.

Also, a stupid-yet-obvious tip: be sure to check the wind direction before you begin spraying. Just wet a finger, hold it up & the cold side is where the wind is coming from.

 

I was not outside. I was not wearing a mask. I was not much far.
I felt nothing wrong...
still... I'm kinda strong on this kind of stuff so... ^^' don't do like me


Kisses

Cacau

 

I spray outside, and for a single face coating (which is done in a few seconds) it isn't worth it to put on my mask; I just hold my breath and turn away. If I'm coating a lot (like whole body), I'd probably get the mask.

Sanding resin on the other hand: wet-sanding and mask. I do NOT want to breathe that dust.

 

The solvents in MSC are toxic--most solvents are, to a greater or lesser extent.

A sanding mask, a surgical mask, or a piece of cloth over your lower face will do Nothing to protect you from solvents.


I tried to get an MSDS (Material Safety Data Sheet) from Dolll & Hobby, but failed.

If someone could get an MSDS from their supplier of MSC, then we could accurately assess the toxicity of the spray & the precautions neccessary.

Ann in CT
could help reading the MSDS & turning it into English

 

WAHHHHH..
I never turned my head or..used a mask!! Mostly I stood a bit back..but I sprayed Unoss today..and I took a Big breathhhh.. :cry: ...this isn't like seriousily bad right..right?

 

If you didn't feel really bad at the time & you don't feel bad now--nose/mouth, throat, windpipe, lungs--you're probably ok.
That's the acute dosage.

I am not a professional, & I've not seen you in any case, so don't take this as 100%.
If you have any problems through any of your respiratory system, please see someone who is a professional.


Ann in CT

 

Ahh my gawd..you're scaring me ...but i feel fine luckely :grin: thankss!!

 

it'd prolly help to do it in a place where it can vent off, such as a bathroom with a vent or even better, outside

 

I would reccomend a mask. Whilst you may not get immediate affects, long term, toxins can do horrible things to you. Better be safe than sorry.

 

One hit is probably not going to do anything long term, more likely to make you cough in the short term. It's prolonged exposure to these things that are the real trouble.

 

This should probably be a little obvious, but don't use an old mask either! My father had a very old one, and I thought it'd be okay to use. Oh no. Inhaling minute rust particles. This was a few years ago, but I do have pretty bad athsma. Just saying, be careful you have a new CLEAN mask, or it could be as horrible as inhaling some MSC.
MSC scares me.. I think I might order some Testor's. At least they sell it in the U.S. Gulp.

 

Same for me...I've used it inside with no mask in my er..."studio" where I do all kinds of painty arty stuff and sewing...I've never gotten sick from chemicals and didn't get sick from MSC, but I guess if I did it a lot for a long time I would.

 

I went to Lowes today to look into getting a heavy duty mask with chambers, but the guy there said that getting such a powerful mask was pretty unnecessary considering how long it takes to spray on a coat of Testors and go back inside for it to dry.

Would a heavy duty styrofoam (or whatever it's made out of) mask be sufficient for just a quick coat of Testors for faceups every now and that? I'd probably also use it to remove faceups and possibly airbrushing. I'd like to start doing commissions in the future which means even more faceups more often, but still not that many uses of Testors.

 

Tell him he doesn't know what he's on about and ask for it anyway.
Testors isn't the time exposure of one "dose"...but more or less; the time exposure over a prolonged amout of time.

Think of how often you breathe for starters; quick or not; you breathe it is; it adds up.
Everytime you face up..you coat testors...at LEAST twice... And you breathe once every oh..say.... 2 seconds.... O.o...so doing the math...we're looking at prolonged exposure.

Iow: get a good mask. I've got one and its got two chambers...but its a dust mask...i use it for resin (that better work...if not someone tell me now). And when i spray testors i turn the vent on (we're on a second floor balcony) , shut the door and open the window...it clears really quickly, and i don't breathe during that time..i've gotten pretty good =n.n=;;...but even with a normal dust mask..i could smell the strong odour of testors..and holding my breathe is the best i've ever done.

 

hoenstly, I don't think you need a heavy duty mask for a 30 second spray, esp if you are spraying outside. it's overkill. might want ot get something lighter.

 

Mine's really light duty, and I've never gotten lightheaded from spraying. This is partly due to the fact that I hold my breath. XD But testors takes longer to spray than MSC, I'd imagine....

 

Now you have me paranoid lol.

I just use one of those paper masks they sell for gardening and the like... I hold my breath while I'm spraying, then jump back fairly quickly and wait... I do it outside in a well ventilated area.

Should I be using a stronger mask? O_o I have yet to feel even a little funny after doing this... I mean other than the little bit I get from holding my breath, that's normal. It's not building up or anything is it?

 

I'm getting a heavy duty mask. I like my lungs, Thank you very much. I have alot of lung problems, second hand smoke, infections, etc. I'd rather not make it any worse than it has to be. It's a very serious thing when you don't use a mask or a don't use the right one. better to be paranoid than be dead.

 

*****n/a*****

 

Such encouraging words. -_-


What rating IS MSC btw? There are many sprays that are fine with a paper mask in a ventalated area, most of which are for sealing art. I learned this in college from professionals. What I'm curious about at this point is, is this a substance that hangs in the air and so continues to be a risk while drying? Or is it a one time settling deal? I will STILL probably get a proper chamber mask at some point before I actually do anything major. But that's also because I need one for something else I'm experamenting with. What I want to know is if the trend of using these things is due to actual saftey, or if one person started doing it and it caught on.

I don't mean to sound rude, and I'm sorry if I'm taking over someone elses topic. I don't mean to be doing either of those things. I simply want to know.

I personally would rather be safe than sorry in most cases. But that doesn't keep me from wishing to know what's right, instead of just what's commonly accepted.

 

*****n/a*****

 

Thank you. *smiles* Now I at least feel a little better *had been wearing protective googles as well*

I will invest in a proper mask then. *nods*

 

I didn't even think about goggles. I could get testor's on my glasses. eew, dullcote eyes.Lol. And you get the added bonus of the nosy neighbors hanging out the windows thining 'what on Earth is she/he doing???"

...Can you imagine having to clean testor's off of glasses? uuuugghhh

 

I got really worried cause I know I should wear a mask since I'm very sensetive but I just couldnt wait. I have been waiting to paint my lil girl for so long and the MSC came this morning!

what I did was to put a thick winder glove over my mouth and nose and tie a scarf around it (must have looked like a freak) and sprayed outside on my balcony since I dont exactly have a garden. the problem is that its kinda stormy outside. not rain but wind, ogh yes. so the thing blew right into my face. I finished spraying, ran in and took some really deep breaths inside. I dont feel bad but jikes, what happens if you breath this stuff? emergency or long-time damage?

 

I would say long term damage.. like smoking.. I am sure this type of stuff causes lung/throat/whatever cancer etc.

Of course concentracted inhalation could cause emergency lung damage, or even death.. just like spraypaints.

Dust masks will do NOTHING to protect you, nor any other makeshift cover.. only masks that protect from particles will protect your lungs..

Read the back of the packages.. dust masks are only for dust.. it isn't even good enough for spray paint.

Please everyone, protect your lungs.. you don't want some bad issue 20 years from now.. especially from something not FDA tested in the USA/Canada, with unknown ingredients

!

 

Since people seem to not know exactly what the chemical composition of MSC is exactly, definitely use a mask. A good rule of thumb is that if you don't know what it's made of and it may be toxic, assume it's carcinogenic. Cover up exposed skin, wear a mask and safety goggles, and always spray in a well-ventilated PET-FREE area. It would be very upsetting to find your dog dead one day from playing in the backyard. I'm sorry if that seems too harsh, but it's very true.

Just because it's available and not regulated doesn't mean it won't kill you. For example, Liquid Nails is available in most hardware shops. It contains chemicals that are known carcinogens. And knowing that most people won't read the safety warnings on the bottle, I just threw away the bottle that I found in my basement. It's not worth the risk if there's an alternative like non death-full Krazy Glue.

SAFETY IS ALWAYS NUMBER ONE. IT IS TOP PRIORITY.

 

Amen to that!

 

My respireator has larger filters than those, but I got it from a contractors supply place in portland (I forget the name) and just told them what I was going to be working with (resin casting, paints) and they gave me the best thing for the job, I also got dust filters. I think the three cartridge sets and mask was under $30 total (I got a student discout, I was snet by an instructor) but yeah, works for dust and fumes of most any kind, its great! I feel to shitty after even spray painting some thing(with out mask), so being able to work all day to no ill effect is such a great thing for realative little money (considering I'd be paying way more in med. bills late in life other wise, since I do this sort of thing a lot!)

 

Wehn I get my Lune it's going to be winter here so not spraying outside.... I'll get a mask and ventilate the basement by opening windows?

 

Either that or a garage, I guess.

 

What _are_ the effects of resin dust? I've been working with/sanding resin garage kits for years and I never heard about resin dust being poisonous before I got into this hobby. All of this talk of what's poisionous and stuff really makes me think I'll send my dolls to someone else to be sanded/coated...

 

http://www.camd.lsu.edu/msds/e/elvacite_2041_acrylic_resin.htm

http://www.hummelcroton.com/msds/cares_m.html

http://www.epa.gov/ttn/atw/hlthef/phthalic.html

http://www.osha.gov/dts/osta/otm/otm_iii/otm_iii_1.html

 

Hah... I use this high toxicity spray mount indoors when trying to put a school project together at the last minute, nothing has ever happened to me, I also once accidentaly breathed in resin dust, again nothing. I use a lot of spray paints for project and all I ever wore was a 'sars' mask. I guess it really just depends on your immunity to these things. I recently just ordered MSC so I'll see how that goes.

 

Does this mean that; if I spray with MSC in the backyard one day, and my dog comes out to play AFTER I'm finish with the MSC, it can die (seeing that dogs usually goes sniffing on the ground, he might inhale some MSC that fell to the ground?)?!?!

Or are you meaning the pet shouldn’t be there while you are using the MSC??

 

Thank you. It sounds like I'm not going to drop dead, it's just probably bad for my asthma to _not_ wear a mask.

 

Probably that you shouldn't have any pets around, and just to be on the safe side, work in an area that you pet doesn't usually play in. Treat it like pesticide; it might not do anything to your dog, but it's better to be safe and prevent a costly hospital bill. It's more that the dog can get very sick, but if the dog isn't treated or the owner doesn't realize something is wrong, things can get a lot worse.

Oh. Looking back on what I said it was pretty harsh... ops: I'm just really touchy about safety. My dad works in safety, so I've just had a lot of stuff drilled into my head. Sorry!

 

The danger with both resin dust and MSC is airborne particulate matter...when I'm sanding outside I'll dump a couple buckets of water on the area I was working in before I let my 3 Pugs out.

 

i know of people who dun use them at all... rofl

oh well i on the fan and use a nurse's mask.... i might ivest in the N95... but the problem u only get 5% of gas thru that mask... rofl...

on another note i am pretty use to seeing and spraying like my friend does in the model shop

 

Okay, first off, forgive me if I sound like a COMPLETE moron..

Now then, I'm getting my 2nd Dollfie in the mail next week. My first one is an SD13 that was already painted, assembled.. the works. Now, this one, is an MSD, that is an assembly kit (as most are). Now, it's a Christmas present to me, so the idea of having everything done, was not thought of. ^.^;;

Now, I've been reading the threads about sanding, coating, face up's, even eyelashes.. and now, I'm TERRIFIED.

I was going to just go out with my list of Testors DullCote, Acrylic Paints, Camel hair #0 Brush, Rubber Art eraser, etc. Since, MSC won't really be able to be shipped to me (my local office here, is like, anal about stuff. I know they'd take it.), and I WANT to buy the volks stuff, but really don't want to wait TOO long, since she'll be here so quick.

Now, I was confident before reading the threads, thinking "oh yea! I could do this!" .. I read one thread that stated that Sanding isn't ENTIRELY necessary, but a matter of preference. So, I was confident (seeing pictures on a random site of before's and after's) that I could get away with NOT doing that. Especially since my health isn't exactly the best right now, and the idea of POISON scares the poo outta me. ^.^;;

Then I read another that stated about the testors, just spray away. heh. Yea, until I read the toxic nature of THAT too. Now, don't get me wrong, I DO have an outside. I don't live in a bubble, but, next week is supposed to be in the single digits as far as temperature goes. So the idea of doing it outside, is out. I would do it in my basement.. but my family likes to hang out there.. namely, my 5 year old. And I'm not about to do anything if it's going to harm her.

So, I thought I'd check up on if THAT is necessary.. bummer, to my understanding it is, at least, if I want to do a faceup. ;.; .. Not to mention, I don't want my MSD yellowing! Regardless of how many people have stated "hasn't happened to mine!". :/ ..

So, here I am. With WAY too many questions, and likely, 90% of them are on different threads. My problem? I'm going out TODAY to get some last minute shopping done. Here's my dillemma.. I need to know what is absolutely 110% necessary to do for my MSD. I WANT to do her make up and stuff. But I really need to know some things before I do. I'm so blind to all of this. ;.;.. So, here goes;

1. In the "Assembly kit" aside from it being in pieces, (i know the wig and eyes are included) do you get the string with it?
2. Are the eyes already IN the head?
3. Is it true that all SD's as of late, were already essentially coated?
4. Does one HAVE to spray the doll before doing the face up?
5. Is there ANY alternatives to coating the doll, that would be essentially SAFE to use indoors?
6. Any tips on ANYTHING I should know?
7. What kind of 'eyelashes' should I buy? Is there an alternative type? (something I can buy at home)
8. What can be used to stick the eyelashes in best, without too much of a mess or problem?

I'm sorry for all these questions, but I'm really kind of scared right now. And, I'd pay someone to do all the work for me, but, I really don't have the money to do that (which is why I'm doing it myself. Otherwise, i'd pay someone else.).

Is it better to just wait? I really want to be able to play with my MSD (and make her some clothes!!!! hehe).. ;.; .. Please, help???..

 

I'm relatively new so I'm not an expert but regarding #4: Yes, you do. Otherwise, you could stain the resin.

 

I don't know about the string, but with a kit, I'm pretty sure the eyes are not in the head..

Kits also probably wouldn't come coated-- in fact, it's possible you may want to clean them before spraying with MSC (or testors)

Yes, you must coat the face otherwise your paint will bead up, or, as inkstone said, you may stain the resin. Because the coating provides a toothed surface to apply paint or other materials to, it's necessary you use it, or it just won't come out right.

As far as alternatives, no, I can't say there are. Unfortunately, all the good stuff tends to be toxic.

You /can/ try to buy human false eyelashes and trim them, but they can look too big or too odd. Doll-made eyelashes are always best, I've found.

As for attaching them, some people use eyelash glue.. but that always annoys me >_> I use superglue, myself... sadly, there's nothing really easy about applying them T_T; it's annoying, but worth it.

I'm sorry it's too cold to spray your kit ;_;

 

3 - no, I do not think so.
4 - Yes you do, or the colors will stain your doll. Not a pretty sight.
5 - No, not that I know of. I know it's a hassle but you should just get MSC
coating spray. ( or other coating sprays that works well with dolls). I have
found some coating mediums you can apply with a brush, but it does not go on well or evenly as the spray.
7 - you can just buy human eye lashes and cut off the ends a bit to make it
shorter. It'll fit your doll. Also, you might want to cut the lashes itself to make it not extrude as much..
8 - the glue used for humans work well. Use a tooth pick to spread the glue on and you're good to go!

hope this helps!

 

Alright, take a deep breath! ^_^ This really isn't nearly as scary as you think it is. My FIRST doll was a volks MSD kit, and she was sanded, strung and ready to play easily and in no time. ^_^

Answers are in reguards to the Volks MSD kits. I'm not sure about the others.
1. Yes, s/he will come with string, and instructions.
2. No, they aren't in the head, but volks will send you some putty (which sucks, and most people use either super sculpty or white "blu-tac" to hold in eyes)
3. No, and certainly not if you are getting a kit. The UV protectant resin is something mixed into the resin on certain limited dolls. Coating is not immediately neccessary either. You can enjoy the doll for a bit before sanding and coating them. Also, chances are your first doll is not body coated at all unless you did it or had someone do it.
4. YES! Things can stain, and it helps any blush stick to the face.
5. In cold weather, I get my winter coat, a large fan, and spray in the garage (ETA: With the outside door open >.< ). If you do just the head you should be fine. I'd wait to spray the body until it gets warmer if you choose to do that. Also, testors might not be the best for full body spraying either. It tends to get gummy when mixed with hand oils.
6. Keeping up coated bodies is a PAIN! It chips and attracts dirt like crazy. If you're ready for some serious upkeep, then go for it. But I coated my mini once, watched it all flake off, and never did again. If you do plan to coat, give the doll a soak in soapy water to get rid of the mold release. The coating won't stick to it. Also, get yourself some pipe cleaners to help with stringing! ^_^
7. You can cut down people eyelashes that you can get at a drugstore or a walmart type store.
8. White "school glue" works best. Most people use tooth picks to help apply the lashes.

I think that's it. Good luck, and don't be worried. These things are a lot easier than you think!

 

*posts her two cents*

1. Yes, the string comes with it.
2. No, the eyes aren't in the head. You'll need some sort of sticky substance to use to keep them in the head (people suggest sculpey, sculpey III, or bluetak).
3. No, only the faceups, when purchased from doll companies, are coated.
4. YES. @_@ Some people tend to say no here, but those people haven't had a stained dollie. >.< Definately, DEFINATELY, spray your dollie's head BEFORE you put any sort of paint or pastels on them. I recommend 3 light coats, with plenty of drying time between (5 minutes each, approx).
5. No.
6. I recommend applying the pastels with a paintbrush, as it gives a very soft and natural look. ^_^ Also, if you're really worried about being 'poisoned', then get a gas mask (about $30 at Walmart), and work near an open window. I've sanded resin before, and never worn a gas mask or any kind of mouth covering and, as far as I know, I'm just fine. ^^
7. I used human eyelashes, but I highly recommend buying eyelashes that are specifically used for SD. Just because you have to trim, and I don't have an eyelash curler, so mine didn't come out very well...
8. I highly recommend Elmer's White Glue (not the school glue stuff, the white glue stuff specifically). I used it for my girl's eyelashes, and they stay perfectly in her head. ^_^ To apply it to the lashes, just very gently pour it onto the end of the eyelashes, where it will attach to the end. Press into the head (people suggest using a toothpick, but I just used my nail), when it's in the perfect position, let sit for about 30 minutes.

Hint with the eyelashes: If they're sticky when you take them out of the package (self adhesive) PULL ALL OF THE STICKYNESS OFF before trying to apply them to the head. @_@ Otherwise when you put the eyes in, the eyelashes will stick to the eyes and come off of the head and you'll have to do it all over again. @_@

That's pretty much it. Don't worry too much. It seems scary, but once you finish, you'll stop and say, 'That wasn't so hard. o.o ^_^' Again, if you're scared about stuff getting in your lungs, just get a gas mask, and leave the window in that room open, and don't use that room for the rest of the day after you're done. ^^; Make sure you have a good area set up, so you don't accidentally spray MSC or Testor's onto the furniture. ^.^;;;

Last thing - sometimes Volks MSD kits don't come with the hook screws (which I assume are used for the hands and feet?), but you can find the correct pieces down at any hardware store or Walmart. ^_^

 

Okay, thanks everyone!
I'm still kind of scared about coating, but, I suppose I could just coat the head, and then leave the body for a warmer date. I suppose that would be okay, right? ^.^;;
I'm not about to sand, because I really don't even want to mess with that. As I understand it (and as I said) it's more a preference.
I think what I will do, is wash her up in mild soapy water (right? would like, regular Dawn be okay?), take the head outside, coat it, wait a few minutes, and then take it inside to finish up.
Anyone have any idea's of how long one should wait? And, should I just stick her on a weighted soda bottle, shut my eyes, hold my arm out, turn my head, take a deep breath, and spray with the course of the wind? heh. I really can't afford a mask (at least, the one's recommended), and let's face it, I really wouldn't be doing more than the head right now anyways. ^.^;; ..
Anyone have ANY suggestions on that? like, how long, and, how to do it? And, how long to let it sit outside (keeping in mind, it's like, anywhere from 15-30 degree's out there right now)?
Oh! And how long after it's been sprayed, and sitting can I begin painting? .. Please let me know. ;D Thanks so much everyone!!!!

 

From what I've read, everyone can remember a bad face-up that they've done. And from the consensus usually everyone cna remember one 'disaster' that's occured while doing a face up. The important and smart thing that you've done is looked up what you needed, and have asked these quesitons before beginning. So Kudos to you!

1. Sorry, I'm not familar with Assembly Kits!
2. See Above.
3. She wouldn't be coated, like others have said.
4. Yep! Usually a couple light coats so that any blushing will stick, and so paint won't bead up. You also give multiple light coats to 'seal' each section of the faceup, once you have it the way you like it.
5. No. However, I do believe that you can coat when it is single digits. Check the back of the can. Usually they give you a temperature range in farenheit.
6. Be patient, and practice spraying (using spray-paint) on a box. It can also be useful to draw a picture of your dolls face on a piece of paper, and practice your techniques and how you want it to look. And don't stress doo much, a face-up can always be removed.
7. You can buy people lashes, and trim the down, but it is a fair amount of work. You can also buy doll lashes too, you'll still probably have to trim them down, but it'll be a lot less trimming!
8. White school glue or tacky glue is usually what people suggest. I'd say rest the head on the pillow upside down in front of you, bunching up the pillow so the head is on an angle. Put some glue on the edge of the lashes, and gently position, poking it into place with toothpicks. Let it dry and ta-da! Pretty lashes!

For some doing face-up's can be a very positive bonding experience with their darling. It takes time, and practice, but you'll soon feel comfortable with your skills. If you have difficult time with your face-ups or if you want some critiques you can post the picture up and have other artists make suggestions. Be sure to post your face-up, we'd love to see how you did! We're all here to support you!

 

Some people even choose not to coat the body at all! It's all a manner of preference. If you'll be doing body-blushing at a later date, coating is recommended.

That sounds right, just make sure the coating is dry before you a) take it in and b) begin working on it.

That's usually how people do it. A mask is recommended but those can be hard to get a hold of. Hold your breath to coat her, then vacate the premises quickly. Wait about 5-10 minutes, then hold your breath again and see if the coating's 'set'. If it looks good and dry, then you can bring it in and let it sit for the rest of the time, before painting. There's usually an approximate time on the back of the can I think.

Look on the back of the can! Usually they give you an approximate time. To be absolutely sure, that's probably the best resource.

Good Luck again!